|
|
LinkBack | Thread Tools | Display Modes |
#12
|
||||
|
||||
Just bolt on in the 4 places with some structural nuts and bolts.
Make sure the side splitters are attached well.
__________________
[COLOR="Gray"]550Nm off a 2L... Just wish it was in the dak dak...[/COLOR] |
#13
|
||||
|
||||
Screws FTW, you'll have to drill holes into your bumper anyway so why not just screw into the plastic.
That's how my S204 one came from the factory like, it had clips and screws. (screws did have little metal washers to catch the thread though) If you're going to use the super long bolts provided, I suggest going and buying some nylon lock nuts to secure them with as the ones provided aren't that great.
__________________
221.7KW-ATW 498.5NM MMS ROLLER DYNO & BUILT BY STi NINJAS, BUILD #318/600 EBISU SUBARU, SHIBUYA-KU TOKYO |
#14
|
|||
|
|||
+ locktite...
|
#15
|
||||
|
||||
Quote:
Lower lip I'd try one of the following: - Buy a guard liner kit and use the bolt and plastic lockers from it to secure to your bumper (this way you'll have self tapping bolts into a secure locking setup) - Alternately source the clips from a guard liner and go from there. - 10/8mill bolts into nuts with washers on either side (as already mentioned would be another goer, if you're going to use locktite just don't be so liberal with it as it'll be a mission to release after its set, where you have the nut use a locking washer in between the the washer and the nut for extra strength. Don't see the point in using either double sided tape or sikaflex for securing a lower lip only as its not going to do anything if the lip moves up or down (based on surface), especially double sided tape as it wont hold jack. Side splitters I'd be using sikaflex and drilling holes where the tapers are (if any), u can use double sided tape to centralise it, but that's all it would be good for).
__________________
[SIGPIC][/SIGPIC] |
#16
|
||||
|
||||
^^^^
sikaflex is the bomb.. 11FC will hold anything and never come off...
__________________
I'm a jockey kunts... |
#17
|
||||
|
||||
Clag Glue?
__________________
[COLOR=Black]Liberty GT Spec B tuned 240 HP & 372 Nm at the hubs.[/COLOR] "Instead of banning high performance cars - ban low performance drivers" |
#18
|
||||
|
||||
tek screws
__________________
RB2666 |
#19
|
||||
|
||||
6" nails
__________________
[COLOR="Blue"]If anyone needs T.I.G or M.I.G or small custom fabrication jobs done PM me.[/COLOR] |
#20
|
||||
|
||||
inb4 aviation grade pop rivets.
__________________
[SIGPIC][/SIGPIC] |
Tags |
bought, front, lip, pu, sti |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
WTB: front lip to suit 99 sti (gc8) | JAY | Wanted | 4 | 25-06-2009 01:24 AM |
MY08-09 STI Front Lips | ULTREX | The Former Workshops Forum | 1 | 28-02-2009 12:11 PM |
99-00 sti front lip | blue.spec | Wanted | 30 | 24-12-2008 02:48 PM |
EOI.how much would u pay for a front lip | philta | General Subaru Discussion | 46 | 28-12-2006 04:33 PM |
Strut Model Numbers | Intra | Mechanicals | 5 | 25-08-2005 06:23 AM |