|
|
LinkBack | Thread Tools | Display Modes |
#11
|
||||
|
||||
Man a lot of people got bitten by that eBay guy huh..... Sigh
Sent from my iPhone using Tapatalk |
#12
|
||||
|
||||
Quote:
Did you get your car fixed man? Sent from my iPhone using Tapatalk |
#13
|
|||
|
|||
Yeah sort of took the car to mao this arvo yeah thinks old maf is fine i was just being to cautious but better safe then sorry he hooked up his diagnostic scanner thingy it popped up maf and knock sensor so we went for a drive and so he cleared ecu with with no problems.he said its fine to drive but if there is a cel again new maf it is. so far so good drove from bently to shoalwater and no cel or shit idle.mao couldn't be more helpful champ
|
#14
|
||||
|
||||
Mao is a champ in things like this. He is always happy to share advice with me too.
|
#15
|
|||
|
|||
Ok then cel came back on yesterday went to mao he said it was knock sensor replace it with new one so today i went to veales and got sensor and installled bitch of a thing to do now i have a constant cel and car is in limp mode which didnt have before and had a intermediate cel and no limp mode help this is driving nuts
|
#16
|
||||
|
||||
Read the codes yourself and see what's faulting.
How to read GC8 CEL codes Followed by resetting your ecu How to reset a GC8 ecu
__________________
[CENTER][SIGPIC][/SIGPIC][/CENTER] [CENTER][COLOR=#ff0000]Built Ej207: Semi-closed RA Cases - Wiseco Forgies - Manley rods - BC 272 cams - GDA Heads - billet f/whl - Vi-pec - WbO2 - 800cc Yellow tops - TD05-20G - 409Hp ath @ 1.75bar on E85[/COLOR][/CENTER] Last edited by Rossco; 19-09-2015 at 02:43 AM. |
#17
|
|||
|
|||
Checked the codes comes up with 22 knock sensor and reset the ecu and still no luck and still in limp mode
Last edited by Gc8beast; 19-09-2015 at 07:20 AM. |
#18
|
|||
|
|||
Anyone have any ideas of whats going on
Cheers |
#19
|
||||
|
||||
Wild guess... Was the knock sensor a direct plug in, or did you have to re-wire it? Does the code go away if you plug the old knock sensor back in? Trying to eliminate a wiring problem or incorrect/wrong/faulty new sensor..
And how did you reset the ECU? Disconnect battery (for how long) or connect green and black connectors under the dash? Last edited by matto20v; 19-09-2015 at 01:17 PM. |
#20
|
|||
|
|||
Yeah it was a direct plug in and the old and new sensor look indentical done the ecu reset by black green connectors havnt tried plugging old sensor in because bitch of a thing to do have to remove ic
|
Tags |
gc8, maf, problem, sensor |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
GC8 MAF wires - soldered, now broken? | vsp44 | Mechanicals | 4 | 12-10-2014 09:27 PM |
GC8 parts - inc. Free dash! | Patch | For Sale | 12 | 03-10-2012 06:42 PM |
GC8 Cluster / HKS Oil Cooler Kit / Recaro Seat Rail & Moreee | blommer | For Sale | 9 | 24-07-2011 04:11 PM |
WTB: GC8 bits (the stuff sitting in your garage) | jEstEr? | Wanted | 1 | 30-12-2006 09:19 PM |